It's so clean and it does what they say it does. I have to say a bad thing or nobody will believe how good these hydrants are: I struggled to clip in a new fitting when the system was under pressure, so I'll shut off pressure if I need to change out fittings to avoid damaging them. That's like a twice a year thing for me. The 3/4" PEX-A attachment is the bomb (photo). After swapping out my old 1/2" copper with 3/4" PEX-A and installing this hydrant my outside GPMs went from 7.5 to 12. Compliment sandwich complete!

Installation was easy. Product seems good so far. Just make sure you have a valve on the hose connector or you will get soaked when connecting.

I bought 2 hot+cold hydrants and 2 V2+hydrants from Aquor, and 3 out of 4 of those worked perfectly but one of the V2's would drip constantly after disconnecting the hose connector. Customer service responded quickly and walked me through some troubleshooting steps to try and dislodge potential debris that might not be allowing the operating rod to close all the way, and after that didn't work, quickly shipped me a warranty unit at no cost. We were under construction, and getting a replacement unit immediately was important, and it arrived within days. Once we removed the "defective" unit, we see that it isn't defective at all but the plumber didn't follow the instructions, and used teflon tape which gummed up the mechanism!

5 stars for Aquor, 10 stars even
1 star for the plumber my GC hired

And my (very constructive) feedback: Aquor should put a large label on the hydrant itself, in both English and (more importantly) in Spanish, stuck to the hydrant in a way that hopefully forces someone to remove and read it before install, reminding them to not use teflon tape and that the o-ring built into the hydrant is sufficient to stop leaks, because nobody will read the manual. And I guess, never trust your contractor and watch everything they do, or... just do it yourself!

These hydrants are extremely well made. Love the fact there is no packing or turning handle that will leak over time. I’ve installed all four myself so not beyond the skills of a decent do-it-yourself homeowner.

I got my first Aquor faucet when I got tired of replacing “frost-free” hose bibs almost every year. After installing the first Aquor I was actually looking forward to the other two hose bibs failing. Fast forward two years and I just replaced my last hose bib with an Aquor. I’ll never use anything else, they’re so easy to use and so reliable. I’ll never again have the dread of cracking open a hose bib for the first time in the spring and watching the vacuum breaker leak water everywhere. Install pictures show the custom mounting block I made out of PVC trim.

So I don't know if you're looking at this product because of the solution of looking clean or because of how well it works. But regardless if there's any products out there that you can consider competition consider this brand because of their customer service. I own four and head an issue with a product that I believe my installer damaged and they covered it. Great customer service will recommend and buy in the future

Purchased the V2 for our new construction home. We we, nor our plumber, were familiar with Aquor, but I knew I wanted them! I chose the Gray polymer which is the least expensive option, and I was afraid it would look cheap. It doesn’t look cheap at all! I might upgrade to a more polished cover later, but this will work with our brick for now! Our plumber wasn’t intimidated with the install and commented on how neat it was! I can’t wait to start using them!

We purchased these faucets and connectors for all of our outdoor faucets, around 9 years ago. Bought them for aesthetics as well as function. Salt air would have nothing to disintegrate. Freezing temperatures would have nothing to burst. And a nice clean look on our home. Loved them. After almost a decade it was time to replace the connectors. The new connectors have a different off and on direction. So far I have replaced them two, possibly three times over. The knob just breaks off because it's not a natural way to turn on and off. Still look great, still prevent freezing. But I question the new direction. Typically its 12 o'clock is off and 6 o'clock is on ( a right turn). New direction is 9 o'clock is off and 3 o'clock is on (a left turn). It does not come natural to us.

I have been working w/ Joe Dunn on a whole house design, which also includes roof located hydrants - V2 hydrants, a H/C hydrant at the garage and in a few months ground mounted hydrants around our home. Each time I have needed design or install assistance, Joe has been there EVERY time. I have also needed on a few occasions to request his support on some urgent shipments along the way, and again Joe has always come thru. He has been excellent to work with and I will be reaching out in a few months to plan the in ground hydrants around the house. Looking forward to trying them out in a few months, and while the house isn’t finished, we have had a number of people ask about them and I know when we are done, they will be a great addition to the value of our home. Thx, Rob

Opted to get an additional connector with flow control to have better management of how much water comes out the hose. This does the trick. This is a tough polymer-based material. Even still, I intend to keep this out of the intense Texas sun when not in use.

We've installed lots of aquor product.. but are really excited about the addition of the no-show mounting box! We are two weeks out from install on the most recent product, and will update when it's complete!

Great Products and Service

Okay, so it’s great except for the fact it does not line up with rest of unit when tight. Preventing removal of valve through the mounting plate hole when in stucco/concrete block configuration. You’d be better off using the straight fitting as short as possible and use a PEX 90 and the adapt PEX into fitting. If the 90 had lined up with rest of valve…easily 5 stars

Very nice well made fitting I had to build a box to mount it as I ordered 12"and should have gone for 10"
Arrived on time happy with purchase.

Good product overall. Best looking hose bib ever.

Great products, have used them on several homes that I have built in my clients seem to love them

Install turned out to be easy and the 7/8th mounting box turned out to be perfect for stucco

So easy to use!

Works great and high quality

Loving this product. Works great and high quality.

I have watched several videos on the Aquor products and looking forward to installing and using on my new build.

We purchased this connector for our hot water shower set up. It's so easy to disconnect the hose and connect the hot water wand. Because this connector has a switch that can be kept in the off position, we just dial it in and it doesn't spray until we're ready. After we're done, just disconnect & reconnect the hose connection. Piece of cake!!!

I purchased this to solve a tricky installation in a crawlspace where space was limited and an elbow was needed. The elbow is made from the same high-quality stainless steel as the V1 Hydrant, and is very easy to install. Additionally, once hand tight, it can be rotated significantly to handle supply lines coming in from any direction without impacting the seal, Aquor had great installation videos that gave me confidence to do this installation myself. I'm very impressed with the company, its products and support.

Pretty slick new products on both the metal finished debris covers (we did some black and white) and also the no show mounting boxes. Being in new construction the exterior trades have a tendency to remove covers and not reset properly so the no show boxes keep a clean look but also makes it a permanent install

The ordering process was great! They got me the exact products I needed.